Author Topic: Original 67-69 Camaro driveshafts - information requested about your car  (Read 340814 times)

69z28rsbilly

  • Member
  • ***
  • Posts: 80
    • View Profile
Re: Original 67-69 Camaro driveshafts - information requested about your car
« Reply #75 on: August 06, 2011, 06:07:29 PM »
Will a 1969 camaro driveshaft fit 1967 to 1969 firebirds ?
Sorry I guess I was referring to the U-joints not the yokes.......
X33 72 72 RS
X33 71 71 RS
X33 10 10

bcmiller

  • CRG Member
  • *****
  • Posts: 4101
    • View Profile
Re: Original 67-69 Camaro driveshafts - information requested about your car
« Reply #76 on: August 06, 2011, 09:24:41 PM »
Length apparently for Firebirds 67-69 was 49.96 for all except TH400 cars which were 49.30 inches.  All 69 Camaro driveshafts were 49.56 inches. 

It may fit.  You will just have to try it and see. 
Bryon / 1968 Camaro SS 396 coupe - now old school 468 big block
1967 Camaro RS/SS 396 coupe L35/M40 - 4 generation family project
Looking for 68 Camaro with body # NOR 181016

sixt9x33rs

  • Hero Member
  • *****
  • Posts: 980
    • View Profile
Re: Original 67-69 Camaro driveshafts - information requested about your car
« Reply #77 on: August 23, 2011, 04:03:20 PM »
69 Z/28

Norwood
03D Car
46.5" length of d/s not including the yoke
clocked
M-21
I will post pictures of stripes later
'69 RS Z/28 65B, 711 Flat hood no spoiler, endura, 4:10 43K miles
69 X77 Z/28 69 69 711 Original Paint Unrestored (Sold)
'69 X66 Convertible 69B 712 auto, (Sold) 44K miles

bcmiller

  • CRG Member
  • *****
  • Posts: 4101
    • View Profile
Re: Original 67-69 Camaro driveshafts - information requested about your car
« Reply #78 on: August 25, 2011, 06:18:53 PM »
I am going to go out on a limb and assume you meant 49.5 inches and not 46.5 inches.   8)

I look forward to the pics of the stripes.  Thanks.
Bryon / 1968 Camaro SS 396 coupe - now old school 468 big block
1967 Camaro RS/SS 396 coupe L35/M40 - 4 generation family project
Looking for 68 Camaro with body # NOR 181016

My68SS

  • Member
  • ***
  • Posts: 491
    • View Profile
Re: Original 67-69 Camaro driveshafts - information requested about your car
« Reply #79 on: September 19, 2011, 04:53:12 PM »
Ok, got my drive shaft out and can report some preliminaries.
Yokes are in-line.
Centers are 49.95"
Bolted straps on diff yoke.
Engine, trans and build as per my sig.

Hi Bryon, sorry for my absence. More info to report.
Have found the orange paint stripe on mine @ 12" approx from the transmission yoke center and what appears to be the green stripe a bit further down - more cleaning needed for that one.


Rob
1968 12C SS
L34/M40
12 bolt posi 3.55

bcmiller

  • CRG Member
  • *****
  • Posts: 4101
    • View Profile
Re: Original 67-69 Camaro driveshafts - information requested about your car
« Reply #80 on: September 20, 2011, 09:54:44 PM »
Thanks Rob.  Check the picture above that Charley posted.  You may have more than 2 stripes.
Bryon / 1968 Camaro SS 396 coupe - now old school 468 big block
1967 Camaro RS/SS 396 coupe L35/M40 - 4 generation family project
Looking for 68 Camaro with body # NOR 181016

bcmiller

  • CRG Member
  • *****
  • Posts: 4101
    • View Profile
Re: Original 67-69 Camaro driveshafts - information requested about your car
« Reply #81 on: October 18, 2011, 05:29:41 PM »
Anybody else ?
Bryon / 1968 Camaro SS 396 coupe - now old school 468 big block
1967 Camaro RS/SS 396 coupe L35/M40 - 4 generation family project
Looking for 68 Camaro with body # NOR 181016

NoYenko

  • Member
  • ***
  • Posts: 351
    • View Profile
Re: Original 67-69 Camaro driveshafts - information requested about your car
« Reply #82 on: October 20, 2011, 02:14:50 AM »
I have a early 69 396 with TH 400, built 1st week in November.Norwood car. All drivetrain original 63K. Drive shaft overall center to center 49 1/4"
U-joints in line. E-clips on caps. Orange stripe 17 1/4" from front, then maybe light blue or green, then dark blue.
Hard to tell I'll post pictures. I am surprised at all the variations.

NoYenko

  • Member
  • ***
  • Posts: 351
    • View Profile
Re: Original 67-69 Camaro driveshafts - information requested about your car
« Reply #83 on: October 20, 2011, 02:16:10 AM »
Missed a picture

plumL78

  • Member
  • ***
  • Posts: 228
    • View Profile
Re: Original 67-69 Camaro driveshafts - information requested about your car
« Reply #84 on: October 21, 2011, 08:18:04 PM »
My 67 big block manual is I believe 50.5.  Best I remember.  We know  Big block shafts are longer

bcmiller

  • CRG Member
  • *****
  • Posts: 4101
    • View Profile
Re: Original 67-69 Camaro driveshafts - information requested about your car
« Reply #85 on: October 23, 2011, 06:38:30 AM »
NoYenko - thanks for posting those pictures!

plumL78 - if you could check that measurement for sure, I would appreciate it.  Thanks.
Bryon / 1968 Camaro SS 396 coupe - now old school 468 big block
1967 Camaro RS/SS 396 coupe L35/M40 - 4 generation family project
Looking for 68 Camaro with body # NOR 181016

bcmiller

  • CRG Member
  • *****
  • Posts: 4101
    • View Profile
Re: Original 67-69 Camaro driveshafts - information requested about your car
« Reply #86 on: February 11, 2012, 08:25:33 PM »
Anybody else?
Bryon / 1968 Camaro SS 396 coupe - now old school 468 big block
1967 Camaro RS/SS 396 coupe L35/M40 - 4 generation family project
Looking for 68 Camaro with body # NOR 181016

67pacer

  • Newbie
  • *
  • Posts: 15
    • View Profile
Re: Original 67-69 Camaro driveshafts - information requested about your car
« Reply #87 on: February 13, 2012, 08:40:13 PM »
Here are some pics of my 69 Z28, LA built, 02C, M20, 49.5 inches, rear strap, BU 0117 G2, clocked 30 degrees, orange and white stripes with a purple splash  closer to the yoke, Also shows some orange on yoke.
Bill

bcmiller

  • CRG Member
  • *****
  • Posts: 4101
    • View Profile
Re: Original 67-69 Camaro driveshafts - information requested about your car
« Reply #88 on: February 14, 2012, 01:08:11 AM »
Thanks 67pacer!  Much appreciated.
Bryon / 1968 Camaro SS 396 coupe - now old school 468 big block
1967 Camaro RS/SS 396 coupe L35/M40 - 4 generation family project
Looking for 68 Camaro with body # NOR 181016

Petes L48

  • Hero Member
  • *****
  • Posts: 822
    • View Profile
Finally remembered to post this:

67 LOS, 11B build, L48 w/ Pglide
49.5 inches center to center, yokes are # 3790024 rear is 280A and front 280D
U bolts, axle is PC1031G 3:31, yokes are clocked