« previous next »
Pages: [1] 2  All

Author Topic: D 80 in AIM?  (Read 11488 times)

68Zproject

  • Hero Member
  • *****
  • Posts: 1869
    • View Profile
D 80 in AIM?
« on: May 18, 2009, 08:56:28 PM »
I haven't been on here in a while.  Did I miss something, as I have searched for hours, about the d-80 not being in the AIM (68 or 69)?
Logged
68Z28

CVKUEBER

  • Member
  • ***
  • Posts: 119
    • View Profile
Re: D 80 in AIM?
« Reply #1 on: May 18, 2009, 09:27:49 PM »
Not in my 68 AIM either. Will have to check my 69 AIM tomorrow.
Logged
GM parts-tech. Polar Chevrolet White Bear Lake, Mn

Mark

  • CRG Member
  • *****
  • Posts: 1089
    • View Profile
Re: D 80 in AIM?
« Reply #2 on: May 18, 2009, 09:34:47 PM »
Its in the 69 AIM, front spoiler only.  Its under Z28 for the rear mostly for paint striping.  Fisher installed the rear spoiler, GM the front.
Logged
Mark C.
1969 Indy Pace Car
350/300HP RPO Z11

rat pack

  • CRG Member
  • *****
  • Posts: 223
    • View Profile
Re: D 80 in AIM?
« Reply #3 on: May 18, 2009, 10:49:37 PM »
You have to look in the 67 AIM for 68 front spoiler mounting as for some reason that page is missing in the reprint of the 68 AIM.............RatPack................
Logged
Just keep livin......L I V I N .............

68Zproject

  • Hero Member
  • *****
  • Posts: 1869
    • View Profile
Re: D 80 in AIM?
« Reply #4 on: May 19, 2009, 03:48:47 PM »
Well, I was kind of looking for a part number or  whatever reference told how to tell if the rear spoiler was GM or repro.  I remember reading it somewhere, but I've searched here quite a while and can't find anything other than the talk of the Camaro emblem being moved up when the factory intalled the spoiler.  I know mine was not factory installed, but am trying to determine if it's even GM and dealer installed.
Logged
68Z28

CVKUEBER

  • Member
  • ***
  • Posts: 119
    • View Profile
Re: D 80 in AIM?
« Reply #5 on: May 19, 2009, 05:03:44 PM »
Should have the casting number of 3916633 if it's a GM spoiler.
Logged
GM parts-tech. Polar Chevrolet White Bear Lake, Mn

68Zproject

  • Hero Member
  • *****
  • Posts: 1869
    • View Profile
Re: D 80 in AIM?
« Reply #6 on: May 19, 2009, 10:09:56 PM »
Quote from: CVKUEBER on May 19, 2009, 05:03:44 PM
Should have the casting number of 3916633 if it's a GM spoiler.

Where?  It's on the car.  Do I need to take it off to find out?  Thanks.
Logged
68Z28

KurtS

  • CRG Coordinator
  • *****
  • Posts: 5979
    • View Profile
Re: D 80 in AIM?
« Reply #7 on: May 20, 2009, 02:14:43 AM »
Yes, the # is on the bottom side.
Logged
Kurt S
CRG

68Zproject

  • Hero Member
  • *****
  • Posts: 1869
    • View Profile
Re: D 80 in AIM?
« Reply #8 on: May 20, 2009, 06:51:38 AM »
OK, thanks.
Logged
68Z28

68Zproject

  • Hero Member
  • *****
  • Posts: 1869
    • View Profile
Re: D 80 in AIM?
« Reply #9 on: May 30, 2009, 06:14:01 PM »
3916633 on the bottom.  More parts I can sell.  P.S.  Anyway to tell if the trunk lid is GM?
Logged
68Z28

rat pack

  • CRG Member
  • *****
  • Posts: 223
    • View Profile
Re: D 80 in AIM?
« Reply #10 on: May 31, 2009, 01:40:53 AM »
Yep, there is a run stamp in the center at the bottom as the repros do not have them......RatPack........
Logged
Just keep livin......L I V I N .............

68Zproject

  • Hero Member
  • *****
  • Posts: 1869
    • View Profile
Re: D 80 in AIM?
« Reply #11 on: May 31, 2009, 05:11:06 PM »
On the raised metal below the jack instructions?  There's what looks like a 3 digit stamp D 8 ?, but I'm guessing as it's painted pretty thick.
Logged
68Z28

JohnZ

  • CRG Member
  • *****
  • Posts: 4365
    • View Profile
Re: D 80 in AIM?
« Reply #12 on: May 31, 2009, 07:58:01 PM »
Quote from: 68Zproject on May 31, 2009, 05:11:06 PM
On the raised metal below the jack instructions?  There's what looks like a 3 digit stamp D 8 ?, but I'm guessing as it's painted pretty thick.

Yup - Fisher Body run numbers are typically three characters - a letter for the stamping plant, and two numbers for the week of the year.
Logged
'69 Z/28
Fathom Green
CRG

68Zproject

  • Hero Member
  • *****
  • Posts: 1869
    • View Profile
Re: D 80 in AIM?
« Reply #13 on: May 31, 2009, 10:39:17 PM »
Argghhh.  I've got a few holes to fix then.  I was hoping it was repro and I'd just get a used trunk lid.  Oh, well.  Thanks gentlemen.
Logged
68Z28

Mark Powers

  • Newbie
  • *
  • Posts: 3
    • View Profile
Re: D 80 in AIM?
« Reply #14 on: June 10, 2009, 01:34:09 PM »
When did the d80 start being on cowl tag
Logged
Pages: [1] 2  All
« previous next »
 

anything