« previous next »
Pages: [1]

Author Topic: Plug wire supports  (Read 7847 times)

sixt9x33rs

  • Hero Member
  • *****
  • Posts: 980
    • View Profile
Plug wire supports
« on: December 19, 2011, 02:49:27 AM »
Would these plug wire supports be correct for a 69 Camaro?

Logged
'69 RS Z/28 65B, 711 Flat hood no spoiler, endura, 4:10 43K miles
69 X77 Z/28 69 69 711 Original Paint Unrestored (Sold)
'69 X66 Convertible 69B 712 auto, (Sold) 44K miles

srode

  • Member
  • ***
  • Posts: 173
    • View Profile
Re: Plug wire supports
« Reply #1 on: December 19, 2011, 10:17:46 AM »
Yep, those are correct.
Logged
Steve - 02D Z11 and a Plain Jane hardtop

sixt9x33rs

  • Hero Member
  • *****
  • Posts: 980
    • View Profile
Re: Plug wire supports
« Reply #2 on: December 19, 2011, 12:47:49 PM »
Quote from: srode on December 19, 2011, 10:17:46 AM
Yep, those are correct.
Did you notice the front loom and the rear loom have angled supports?

Thanks
Logged
'69 RS Z/28 65B, 711 Flat hood no spoiler, endura, 4:10 43K miles
69 X77 Z/28 69 69 711 Original Paint Unrestored (Sold)
'69 X66 Convertible 69B 712 auto, (Sold) 44K miles

srode

  • Member
  • ***
  • Posts: 173
    • View Profile
Re: Plug wire supports
« Reply #3 on: December 19, 2011, 11:53:12 PM »
Yes, the front one is for the temperature sending wire, the back one is for the 2 plug wires from the 2 front cylinders.
Logged
Steve - 02D Z11 and a Plain Jane hardtop

sixt9x33rs

  • Hero Member
  • *****
  • Posts: 980
    • View Profile
Re: Plug wire supports
« Reply #4 on: December 20, 2011, 01:33:37 AM »
thanks
Logged
'69 RS Z/28 65B, 711 Flat hood no spoiler, endura, 4:10 43K miles
69 X77 Z/28 69 69 711 Original Paint Unrestored (Sold)
'69 X66 Convertible 69B 712 auto, (Sold) 44K miles

JohnZ

  • CRG Member
  • *****
  • Posts: 4365
    • View Profile
Re: Plug wire supports
« Reply #5 on: December 20, 2011, 08:37:12 PM »
Quote from: srode on December 19, 2011, 11:53:12 PM
Yes, the front one is for the temperature sending wire, the back one is for the 2 plug wires from the 2 front cylinders.

Actually, the temp sender wire goes in the center slot; see the Assembly Manual, UPC 12, sheet A7.
Logged
'69 Z/28
Fathom Green
CRG

srode

  • Member
  • ***
  • Posts: 173
    • View Profile
Re: Plug wire supports
« Reply #6 on: December 20, 2011, 10:33:16 PM »
My mistake not being more clear, I meant the ramp that points to the rear of the engine on the front bracket holds the wire.  I didn't notice the split in the middle of that bracket holds the wire also, but it does. Learn something new everyday.
Logged
Steve - 02D Z11 and a Plain Jane hardtop

69DuskBlueRS/Z28

  • Newbie
  • *
  • Posts: 12
    • View Profile
Re: Plug wire supports
« Reply #7 on: August 23, 2023, 01:39:46 PM »
Does anyone know the part number or a source to purchase the left outboard spark plug wire support (Cylinders 1 & 3) that also holds the temperature sending unit wire?  It is shown in "sixt9x33rs''s second photo, also shown on page 11 in Jerry's '69 book as well as UPC 12 sheet A7 on page 158 in the assembly manual.  Any help would be most appreciated. 
Logged

169INDY

  • Hero Member
  • *****
  • Posts: 1892
    • View Profile
Re: Plug wire supports
« Reply #8 on: August 23, 2023, 05:39:41 PM »
These can be found by the millions of small block vehicles recycled or at swap meets.
I found these off of a 350 powered station wagon, stripped sent to plater now needed plastic coated. The tool handle dipping in a can product will work but is not meant for the heat and oil environment of an engine compartment. A true "Plastisol" dip would be best but difficult to source. *( the "can" will have to do)
aka: Military Specification Plastisol meeting MIL-P-20689 and A-A-59464. Automotive Specification Plastisol ESB-M4D148-A GM225M GM7001M and MS-DC513.

These might be repoped see Heartbeat Camaro as an option.?
Logged
Jim
68 SS/RS L35 Th-400 LOS
69 Pace Car L48 Th-350 LOS
68 Z28 M21 LOS

Leon in Mn.

  • Member
  • ***
  • Posts: 69
    • View Profile
Re: Plug wire supports
« Reply #9 on: August 23, 2023, 06:42:30 PM »
Looking for big block wire supports.  Although they are out there, I can't seem to find the correct ones for my 67.  Any ideas?
Logged

69DuskBlueRS/Z28

  • Newbie
  • *
  • Posts: 12
    • View Profile
Re: Plug wire supports
« Reply #10 on: August 23, 2023, 09:19:51 PM »
Thank you, 169Indy.
Logged
Pages: [1]
« previous next »
 

anything