Messages

1

Restoration / Re: D91 stripe & RPO Z21

« on: October 27, 2015, 08:38:25 PM »

Thanks for your help gents, I was looking around there yesterday but obviously didn't pay enough attention.
Thanks again

2

Restoration / Re: D91 stripe & RPO Z21

« on: October 27, 2015, 11:02:05 AM »

the information I have gathered over the last few months on this vehicle is hopefully correct.
Yes on the build sheet it has option D91 and has the option Z21. It was, well I am meant to believe it was just a 327 2 speed vert.

3

Restoration / Re: D91 stripe & RPO Z21

« on: October 27, 2015, 10:35:25 AM »

Yeah mate it's a 68
I have looked on this CRG info but I can't see it being a D96 stripe.

4

Restoration / D91 stripe & RPO Z21

« on: October 27, 2015, 07:33:40 AM »

Have been trying on the net an image of the D91 stripe and the fender pin sripe which comes with the RPO Z21 option but can not seem to find any thing. I am trying to get my car back to original.
Thanks in advance.
Can someone please point me in the right direction

5

Decoding/Numbers / Re: 8 or B for 1968

« on: July 16, 2015, 06:02:26 AM »

I found the partial VIN just under the air intake - wipers. Yep it is an 8 and the rest of the numbers match.Just have to take a squiz under that dodgy tag to see what the go is..

6

Decoding/Numbers / Re: 8 or B for 1968

« on: July 14, 2015, 08:42:16 PM »

There you go.
Definatatly a dodgy then by looking at your originals above.looks like I will have to pull the dash out and see what is really behind there.

7

Decoding/Numbers / Re: 8 or B for 1968

« on: July 13, 2015, 09:51:53 PM »

Sorry Kurt, the stamp is located on the (your) drivers side dash.The car is over here is Oz.

8

Decoding/Numbers / Re: 8 or B for 1968

« on: July 13, 2015, 08:29:47 PM »

Thanks for the replies. A yarn means a chat..the car is located in Aust. I may have to pull the whole dash out to take a better look.

9

Decoding/Numbers / 8 or B for 1968

« on: July 13, 2015, 11:23:21 AM »

Gday gents,
This is the VIN on my 68 convertible
As you can see there seems to be a B stamped where the 8 should be..is this common ? or is there something sinister going on here.

10

Decoding/Numbers / Re: confirmation 400 ?

« on: June 28, 2015, 05:43:21 AM »

Thanks.
The pan is that 350 shape so that's good.I looked up that town and it is near Detroit ?
Here is a better look at that other tranny number which is stamped up front on your drivers side near the block.

11

Decoding/Numbers / Re: confirmation 400 ?

« on: June 27, 2015, 07:54:45 PM »

Sorry missed the bottom tranny #
Pretty hard to see

12

Decoding/Numbers / Re: confirmation 400 ?

« on: June 27, 2015, 07:51:13 PM »

Thanks Kurt,so I its a 73 400 block 2 bolt.
Here is a closer number of the tranny and I put another coupla pics in ..there is another number on bottom of tranny its pretty hard to see and also the number on the front of the motor..I seem to have a problem with this one.

13

Decoding/Numbers / confirmation 400 ?

« on: June 27, 2015, 02:59:16 AM »

Hi guys....just like to confirm these numbers if anybody could help.
I think it is a 73 400 block ?? Not sure of the numbers on tranny - supposed to be a TH350
What you think ??
Thanks.

14

General Discussion / Re: aussie 68

« on: June 24, 2015, 10:40:01 PM »

Thanks Paul
Hope this comes through..the old girl has not got all the numbers matching in fact they seem to be all over the joint..ha I have bought a couple of parts from over there the quality wasn't too bad.Who do you think are the best people/company to get new parts from? ?

15

General Discussion / Re: aussie 68

« on: June 24, 2015, 08:08:51 AM »

Thanks for  the feedback
I  have to and figure out how to make these pictures smaller so they will send