Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - clean68rs

Pages: [1] 2 3
1
Decoding/Numbers / Re: Identifying this big block
« on: January 14, 2015, 12:52:13 AM »

 Thanks for the help. I know more now then when I started.

2
Decoding/Numbers / Identifying this big block
« on: January 12, 2015, 02:21:29 AM »
I have a 454 big block here and would like to know more about it here are some numbers. casting #14015445 also on left side #4234166802.  Above where the oil filter installs this is cast in  the block  k14    Thanks for any help.
              445
          Hi Perform
             Pass                           


                                                                                                         
                                                                                                                                                                                             

3
Decoding/Numbers / Re: Vin check please
« on: January 11, 2015, 02:45:23 PM »
Thank you Paul

4
Decoding/Numbers / Vin check please
« on: January 11, 2015, 02:35:16 AM »
 
   Can someone trace this vin# 124277N186173     A person is looking to buy this car and would like to know if its the real deal. This is what he has been told. 1967 ss four speed with a 327 original car. Any help would be great. We don't want him to get taken thank you Scott.

5
Decoding/Numbers / Re: vin numbers
« on: April 26, 2014, 09:29:25 PM »

  I will post more info when I get some. Right now it still blocked in by a mountain of horse crap. Still have to cut stump down to pull it out.

6
Decoding/Numbers / Re: vin numbers
« on: April 24, 2014, 12:27:45 PM »
 I am told that the car  came with a 350 with a 2 speed power glide. Could it still be a ss car with that set up. The car is sitting on horse crap right now once we pull it out will be able to do some more research. Thanks for posting I will keep looking deeper in to this car.

7
Decoding/Numbers / Re: vin numbers
« on: April 24, 2014, 01:05:09 AM »

   
More numbers  These are from the tag on the fire wall.  S T 68-12437   nor 81729    lower on the tag It reads    T R 712       U2

The car has manual brakes drum on all four. Has an ss hood but not much else to go on. Automatic tranny. That's about it.  Can these numbers be identified. Thanks

8
Decoding/Numbers / Re: vin numbers
« on: April 22, 2014, 02:09:07 AM »

 Thank you for the help. That would be something if it was a rare find. Ill let you know what we find out.

9
Decoding/Numbers / vin numbers
« on: April 22, 2014, 01:33:23 AM »

   I have found a 1968 Camaro behind a house and the owner is ready to sell. I would like to know if anyone could give me info using these vin numbers. VIN 124376N3B1579   The number 6 may or may not be that number. could not get a good look at them. Will be going to look at it tomorrow with the person that found it. Would be nice if this turned out to be an original ss or something special.

10
Mild Modifications / Re: 8.2 10 bolt differential
« on: December 22, 2013, 01:44:31 AM »

 Thanks again. I am learning a lot from all your replies.

11
Mild Modifications / Re: 8.2 10 bolt differential
« on: December 20, 2013, 03:10:35 AM »

  Thank you everyone for your replies.

12
Mild Modifications / 8.2 10 bolt differential
« on: December 19, 2013, 02:10:00 AM »
How much power can you put to the 8.2 rear end. I have been reading up on them and they don't get good reviews. Anyway I'm installing a Powertrax locker to get the pozzy traction.

13
Originality / Re: wheel opening moldings
« on: January 06, 2013, 02:35:50 AM »
Thank you William for helping me out with that. Ive looked at so many different pictures and seen them done so many diffrent ways I didnt know what to think. Thanks again Scott.

14
Originality / wheel opening moldings
« on: January 04, 2013, 01:16:30 PM »
I have a 68rs and my question is, should the front wheel well molding be full length and the rear wheel well molding end at the side quarter panel molding? In the catalogue that is the way it is suggested. I just would like to know if this is the way thay came stock. Thank you Scott.

15
Decoding/Numbers / Re: 10 bolt rearend
« on: November 26, 2012, 02:28:43 AM »
Thank you Ed for that information. Scott

Pages: [1] 2 3
anything